21-5. Autocad Modeling Extrude 3D Draw
How to convert 2D Draw to 3D object inwards AutoCAD?
EXTRUDE command on the MODELING toolbar is used to "shift" an object (which was previously treated) REGION command.
Command tin survive run inwards ascendence business prompt => EXTRUDE
Pay attending to the sub-command for the ascendence EXTRUDE.
Extrude tin apply to:
- Lines
- Arcs
- Elliptical arcs
- 2D polylines
- 2D splines
- Circles
- Ellipses
- Planar 3D faces
- 2D solids
- Traces
- Regions
- Planar surfaces
- Planar faces on solids
- Lines
- Circles
- Arcs
- Ellipses
- Elliptical arcs
- 2D polylines
- 3D polylines
- 2D splines
- 3D splines
- Edges of solids
- Edges of surfaces
- Helixes
The subcommand afterwards each press Enter push clitoris you lot accept for sure options for additional elements Extrude (elevation lines or object) .
Extrude an object is done equally follows:
- - Create an object (must survive a shut surface area unless extrude line)
- - Activate ascendence ISOLINES (number of lines) + Enter
- - Click on the Extrude
- - Select the object + Enter
- - Pay attending to the clause direct 1 of them, or exactly larn into the elevation of the building.
Command: _extrude
Current wire frame density: ISOLINES = fifty
Select objects to extrude: 1 constitute
Select objects to extrude:
Specify elevation of extrusion or [Direction/Path/Taper angle] <64.1171>:
When working amongst the main ascendence orders should survive noted that the selection of 1 of them may accept an additional sub-command for the eventual completion as well as completion of commands inwards AutoCAD.
So you lot encounter the higher upward representative is:
- Direction => Extrude Direction
- Path => path past times which to extrude an object
- Taper Angle => angle that volition extrude the object that is narrow at the halt of this height. (Here banknote that you lot tin extrude the circle equally a number snuff it a cone or truncated cone. Taper Angle ,so when narrowing the angle extrude)
EXAMPLE: Extrude lines that are angled xc ° as well as the oblique angle (if you lot extrude the business hence you lot snuff it the expect of the network equally a starting point).
Current wire frame density: ISOLINES = fifty
Select objects to extrude: 1 constitute
Select objects to extrude:
Specify elevation of extrusion or [Direction/Path/Taper angle] <64.1171>:
When working amongst the main ascendence orders should survive noted that the selection of 1 of them may accept an additional sub-command for the eventual completion as well as completion of commands inwards AutoCAD.
So you lot encounter the higher upward representative is:
- Direction => Extrude Direction
- Path => path past times which to extrude an object
- Taper Angle => angle that volition extrude the object that is narrow at the halt of this height. (Here banknote that you lot tin extrude the circle equally a number snuff it a cone or truncated cone. Taper Angle ,so when narrowing the angle extrude)
EXAMPLE: Extrude lines that are angled xc ° as well as the oblique angle (if you lot extrude the business hence you lot snuff it the expect of the network equally a starting point).
Here, banknote that you lot can't drawn a rectangle of base of operations business extrude a 3D model. You must procedure the rectangle REGION command (to all iv lines connect to 1 area).
EXAMPLE: Extrude the rectangle as well as circle. The amount, type or specify a mouse.
EXAMPLE: Extrude a circle amongst a cone as well as truncated cone as well as rectangle inwards the pyramid as well as truncated pyramid.
Command: _extrude
Current wire frame density: ISOLINES = 50
Select objects to extrude: 1 found
Select objects to extrude:
Specify elevation of extrusion or [Direction/Path/Taper angle]: T
Specify angle of taper for extrusion <35>: 10
Specify elevation of extrusion or [Direction/Path/Taper angle]: 50
EXAMPLE: Extrude a circle inwards the subway scheme using a sub-command Path
I suggest that business the path to convert Polyline (otherwise you lot can't unmarried click direct the entire path). Therefore, I showed that the to a greater extent than lines as well as ports you lot tin specify a path to extrude.
Command: _extrude
Current wire frame density: ISOLINES = fifty [number of lines - Variable]
Select objects to extrude: 1 constitute [after selecting the object amongst the mouse]
Select objects to extrude: [If you lot want to direct other objects yet accept the choice for it] + Enter
Specify elevation of extrusion or [Direction/Path/Taper angle] <-12.1287>: P [optional path]
Select extrusion path or [Taper angle]: [Click on the business trajectory.]
After applying the EXTRUDE ascendence number of this. With this command, I drew the drawing of the household gutters inwards representative 3D depict a House (from this Blog tutorials). And of course of teaching additional SUBRTACT ascendence took the object to snuff it a hollow tube.
ATTENTION: (Unable to extrude the selected object.)
If you lot snuff it the inability Extrude object survive that the path to an object located inwards the same plane, because a skilful banknote the persuasion (use the push clitoris 3D Orbit) to rotate an object inwards space!